Estes 2053 - Paveway Manuel d'utilisateur télécharger pdf

ESTES

INDUSTRIES

1295 H Street

Penrose, CO 81240

PRINTED IN CHINA

www.estesrockets.com

PARTS:

Locate the parts shown below and lay them out on the table in front of you. DO NOT

USE THIS DRAWING TO ASSEMBLE YOUR ROCKET.

ASSEMBLY TIP:

Read all instructions before beginning

work on your model. Make sure you have

all parts and supplies.

KEEP FOR FUTURE REFERENCE.

HELPFUL HINT:

IF NOSE CONE/COUPLER FIT IS. . .

TOO

TIGHT

TOO

LOOSE

ADD

MASKING TAPE.

SAND FOR FIT.

FLYING MODEL ROCKET KIT INSTRUCTIONS

EST 1247/2053

TEST-FIT ALL PARTS TOGETHER

BEFORE APPLYING ANY GLUE!

If any parts don’t fit properly, sand as required

for precision assembly.

Body Tube BT-55 (1)

(30374)

Die Cut Balsa Sheet (2)

(32218)

Centering Ring Card (1)

(30126)

Mylar Retainer

Ring (1)

(30168)

Green Engine

Block (1)

(30162-2)

Shock Cord (1)

1/8" x 18"

(38374)

Assembled 12” (30 cm) Parachute

(35801)

Plastic Tail Cone and

Adapter (1)

(60568)

Decal Sheet (1)

(60569)

Die Cut Balsa Sheet (1)

(32219)

SHOCK CORD

MOUNT

SECTION

SHOCK CORD

MOUNT

SECTION

FIN

TUBE MARKING GUIDE

MATCH LINES

UPPER TUBE MARKING GUIDE

GBU-24 PAVEWAYIII EST 2053

Operation Enduring Freedom

sticker (1)

(60586)

Nose Cone (1)

(60567)

Yellow Spacer Tool (1)

(35003)

Launch Lug (1)

(38178)

Body Tube BT-20 (2)

(30329)

Engine Hook (1)

(35021)

SUPPLIES

In addition to the parts included in the kit you will also need:

SCISSORS PENCIL

RULER

FINE

SAND PAPER

(#400-600 GRIT)

CARPENTER’S

GLUE

MASKING

TAPE

SPRAY

PRIMER

WHITE

SPRAY PAINT:

WHITE, OLIVE

DRAB, RED

PLASTIC

CEMENT

MODELING

KNIFE

SPRAY

DULL

COAT

RAZOR SAW

SILVER PAINT

PEN

1 2 3 4 5 6

Résumé du contenu

Page 1 - SUPPLIES

ESTES® INDUSTRIES1295 H StreetPenrose, CO 81240PRINTED IN CHINAwww.estesrockets.comPARTS:Locate the parts shown below and lay them out on the table in

Page 2 - . PREPARING FINS

1. ASSEMBLING ENGINE MOUNTI" mark(25 mm)C. Stack like pieces and sand edgessmooth. Leave the edges square,do not round them.A. Fine sand balsa s

Page 3 - . ASSEMBLING LOWER FINS

"LL"3. MARKING BODY TUBESSHOCK CORDMOUNTSECTION3SECTION2SECTION1SHOCK CORDMOUNTSECTION3SECTION2SECTION1FINFINFINFINTUBE MARKING GUIDEMATCH L

Page 4 - . ASSEMBLING UPPER FINS

ASSEMBLING FIN REINFORCEMENTS7. ATTACHING SHOCK CORD & ASSEMBLING UPPER BODY TUBEA. Mark body tube 3/4" (19 mm)from end on each fin line.3/4&

Page 5 - . ATTACHING PARACHUTE

ROCKET PREFLIGHTE. Wrap lines loosely. Insertparachute, shock cord,then upper assembly.A. Insert four squares of loosely crumpledrecovery wadding into

Page 6 - MISFIRES

COUNTDOWN AND LAUNCHFLYING YOUR ROCKETChoose a large field (500 ft. [152 m] square) free of dry weeds and brown grass. The largerthe launch area, the