Estes 2190 – Cosmos Mariner Manuel d'utilisateur télécharger pdf

ESTES INDUSTRIES

1295 H Street

Penrose, CO 81240

#2190

FLYING MODEL

ROCKET KIT

INSTRUCTIONS

www.estesrockets.com

KEEP FOR FUTURE

REFERENCE

ASSEMBLY TIP: Read all

instructions before beginning work on

your model. Make sure you have all

parts and supplies.

TEST FIT ALL PARTS TOGETHER

BEFORE APPLYING ANY GLUE!

If any parts don't fit properly, sand as

required for precision assembly.

PARTS Locate the parts shown below and lay them out on the table in front

of you. DO NOT USE THIS DRAWING TO ASSEMBLE YOUR ROCKET.

SUPPLIES In addition to the parts included in the kit you will also need:

SCISSORS

CARPENTER'S

GLUE

PLASTIC

CEMENT

PRINTED IN CHINA

PENCIL RULER

CELLOPHANE

TAPE

MODELING

KNIFE

MASKING

TAPE

• SPRAY PRIMER

• SPRAY PAINT

(TAN, GOLD, GRAY)

• SPRAY CLEAR COAT

(OPTIONAL)

DIE CUT

CARD (1)

(32477)

CLAY WEIGHT (2)

(85705)

page 12

PN 60842 (02-05)

FLYING YOUR ROCKET

Choose a large field (500 ft. [152 m] square) free of dry weeds and brown grass.

The larger the launch area, the better your chance of recovering your rocket. Football

fields and playgrounds are great. Launch only with little or no wind and good visibility.

Always follow the National Association of Rocketry (NAR) SAFETY CODE.

MISFIRES

TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE

GOING NEAR THE ROCKET!

Disconnect the igniter clips and remove engine. Take

the plug and igniter out of the engine. If the igniter has burned, it worked but did

not ignite the engine because it was not touching the propellant inside the engine.

Put a new igniter all the way inside the engine without bending it. Push the plug in

place. Repeat the steps under Countdown and Launch.

NAR Safety Code

NO DRY GRASS

OR WEEDS

PRECAUTIONS

COUNTDOWN AND LAUNCH

KEY

ALWAYS

OUT UNTIL FINAL

COUNTDOWN!

2...

HOLD KEY DOWN AND

PRESS LAUNCH BUTTON

UNTIL

LIFTOFF!

4...

INSERT KEY.

PUSH DOWN

FIRMLY AND

HOLD.

MASKING

TAPE

KEY

4... 3... 2... 1...

5...

15 FT. (5 M)

3...

10" (25.4 cm)

1...

X PRIZE is a registered trademark

of the X PRIZE Foundation and is

used by permission.

SILICONE

ADHESIVE

FUSELAGE TUBE

BT-55 (1) 14-1/8" (35.9

cm) (30470)

WEIGHT ASSEMBLY

TUBE BT-760 (1)

(30472)

UPPER FUSELAGE

(1) (60966)

BOTTOM FUSELAGE

(1) (60967)

PLASTIC DOOR

(1) (60968)

WIRE FORM

(1) (60987)

ENGINE HOOK

EH-2 (1) (35021)

BLACK ENGINE

HOOK RETAINER

RING (1) (30160)

YELLOW

SPACER TOOL

(1) (35004)

PLASTIC

POD END

RING (1)

(60969)

PLASTIC

POD RING

(1) (60970)

PLASTIC

POD CAP

(1) (60971)

PLASTIC

DISPLAY

NOZZLE

BASE (1)

(60972)

PLASTIC

DISPLAY

NOZZLE (3)

(60973)

BULKHEAD RING

AR-76055 (GREEN)

(1) (30133)

CENTERING RING

(GREEN) AR-76050

(3) (30004)

STEEL WASHER

(4) (38330)

LASER CUT BALSA SHEET (2) (32230)

LASER CUT BALSA SHEET (1) (32231)

ASSEMBLED

PARACHUTE 18"

(46 CM) (1) (35802)

DOUBLE-SIDED

DOOR TAPE (2)

(60988)

LAUNCH LUG

3/16" X 2" LL-3B (1)

(38166)

ELASTIC THREAD

ET-1 (1) (85772)

DECAL SHEET (1) (60843)

ENGINE POD TUBE BT-

1000 (1) 13-7/16" (34.1 cm)

(30471)

SAND

PAPER

WAX

PAPER

NOTE: So that you

don't loose sight of

your glider or

engine pod, it's a

good idea to have

another person

observe the

launch and

recovery, as the

glider and engine

pod descend

separately.

1 2 3 4 5 6

Résumé du contenu

Page 1 - PRECAUTIONS

ESTES INDUSTRIES1295 H StreetPenrose, CO 81240#2190FLYING MODELROCKET KITINSTRUCTIONSwww.estesrockets.comKEEP FOR FUTUREREFERENCEASSEMBLY TIP: Read al

Page 2 - 15. PREPARE FOR FLIGHT

3/4"(19 mm)A. Mark tube 7/8" (22 mm)from front.COMPLETED ASSEMBLY1. ASSEMBLE ENGINE POD WEIGHT ASSEMBLYB. Apply glue around tube in front of

Page 3 - 14. GLIDE TEST

ALIGNCOMPLETEDENGINE POD TUBEASSEMBLYI. Align wire form as shown, tips forward. Loop goes over tube.Press wire form rearward until it fits into notch

Page 4 - 4. ASSEMBLE WING

page 4 page 94. ASSEMBLE WINGA. Sand balsa sheetssmooth, both sides.WAX PAPERB. Using a modelingknife, carefullyremove balsaparts from sheets.C. Sand

Page 5 - 9. ATTACH PARACHUTE

ENGINEPOD TUBEpage 5page 85. ATTACH FUSELAGE TUBE TO WINGSDOORFRAMEA. Using a door frame,draw a line theentire length of thetube.C. Glue tube to wing

Page 6 - 8. ATTACH LAUNCH LUG

page 6C. Apply glue to bottomleft stabilizer. Align tabon stabilizer with slotin wing and attachstabilizer to wing.Repeat for rightbottom stabilizer.N

Commentaires sur ces manuels

Pas de commentaire

Estes 2190 – Cosmos Mariner Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Estes 2190 – Cosmos Mariner. Estes 2190 – Cosmos Mariner User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Estes 2190 – Cosmos Mariner