Estes 1265 – Scissor Wing Transport Manuel d'utilisateur télécharger pdf

KEY

SCISSOR WING TRANSPORT

ESTES INDUSTRIES

1295 H Street

Penrose, CO 81240

#1265

FLYING MODEL ROCKET

KIT INSTRUCTIONS

www.estesrockets.com

KEEP FOR FUTURE REFERENCE

ASSEMBLY TIP: Read all instructions

before beginning work on your model.

Make sure you have all parts and supplies.

TEST FIT ALL PARTS TOGETHER

BEFORE APPLYING ANY GLUE!

If any parts don’t fit properly, sand as

required for precision assembly.

PARTS Locate the parts shown below and lay them out on the

table in front of you. DO NOT USE THIS DRAWING TO ASSEMBLE

YOUR ROCKET.

PRINTED IN CHINA

BODY TUBE BT-50 18" (1)

(30352)

POWER POD BT-20 12" (1)

(30451)

RUDDER TUBE BT-50J 2-3/4" (1)

(30362)

ENGINE HOOK

EH-2A (1)

(35021)

GREEN CENTERING

RINGS AR2050 (2)

(30164-2)

LAUNCH LUG

LL2B (1)

(38178)

GREEN ENGINE

BLOCK AR520 (1)

(30162-2)

MYLAR RETAINER

RING (1)

(30168)

CLAY WEIGHT (1)

(85704)

YELLOW SPACER

TOOL ET-2 (1)

(35003)

RUBBER BAND #8 (2)

44060

WOOD DOWEL 1/8" X 9"

(32054)

ELASTIC THREAD ET-1

(85772)

PLASTIC PARTS SET (60832)

NOSE CONE INSERT

PIN-50 YR (1)

(72605)

PLASTIC NOSE CONE

PNC-50YR (1) (72604)

ASSEMBLED 12" (30 cm)

PARACHUTE (1)

(35801)

DECAL SHEET WITH TAPE HINGES (37065)

LASER CUT BALSA SHEET 1/8" (3 mm) 32229

LASER CUT BALSA SHEET 1/16" (2 mm) (32228)

WING

PIVOT CAP

WING

PIVOT

PIVOT BASE

WING

HOLDER

SUPPLIES In addition to the parts included in the kit you will also need:

SCISSORS PENCIL RULER FINE SAND

PAPER

(#400-600 GRIT)

CARPENTER’S

GLUE

HOBBY

KNIFE

PLASTIC

MODELING

CEMENT

MASKING

TAPE

RAZOR

SAW

TWEEZERS SPRAY

PRIMER

WHITE

SPRAY

PAINT:

BLACK

WHITE

12.

FLYING YOUR ROCKET

Choose a large field (500 ft. [152 m] square) free of dry weeds and brown grass. The

larger the launch area, the better the chance of recovering your rocket. Football fields

and playgrounds are great. Launch only with little or no wind and good visibility.

Always follow the National Association of Rocketry (NAR) Safety Code.

MISFIRES

TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE GOING

NEAR THE ROCKET! Disconnect the igniter clips and remove the engine. Take the

plug and igniter out of the engine. If the igniter has burned, it worked but did not ignite

the engine because it was not touching the propellant inside the engine. Put a new

igniter all the way inside the engine without bending it. Push the plug in place. Repeat

the steps under Countdown and Launch.

NAR Safety Code

NO DRY GRASS

OR WEEDS

P/N 83130 (1-05)

COUNTDOWN AND LAUNCH

ESTES LAUNCH SUPPLIES

To launch your rocket, you will need the following:

¥ Porta-Pad

II Launch Pad

¥ Electron Beam

Launch Controller

¥ Recommended Engines: B4-2, B6-2, C6-3

¥ Igniters and Igniter Plugs (included with Estes engines)

KEY ALWAYS OUT UNTIL

FINAL COUNTDOWN!

HOLD KEY DOWN AND PRESS

LAUNCH BUTTON UNTIL

LIFT-OFF!

15 FT. (5 M)

4... 3... 2... 1...

INSERT KEY.

PUSH DOWN

AND HOLD.

1...

2...

4...

PRECAUTIONS

MASKING

TAPE

8 (20.4 cm)

LAUNCH BUTTON

3...

NOTE: So that you don’t lose

sight of your Glider or

Power Pod, it’s a good idea

to have another person

observe the launch, as the

Glider and Power Pod

descend separately.

1 2 3 4 5 6

Résumé du contenu

Page 1 - PRECAUTIONS

KEYSCISSOR WING TRANSPORTESTES INDUSTRIES1295 H StreetPenrose, CO 81240#1265FLYING MODEL ROCKETKIT INSTRUCTIONSwww.estesrockets.comKEEP FOR FUTURE REF

Page 2 - PREPARE ENGINE

REFERENCE SHEET & MARKING GUIDES2. 11.BALSA SHEETSNOT TO SCALEPLASTIC PARTSNOT TO SCALETUBE MOUNT SPACERDOWEL MOUNT CENTERWING1/8" LASER CUT

Page 3 - BALANCE GLIDER

BODY TUBEBOTTOM VIEWRUBBER BANDWING AT 45ß2-1/2" (6.4 cm)1-7/16" (3.7 cm)2" (5.1 cm)1/8"(3 mm)1/2" (13 mm)MASKINGTAPE10. 3.B

Page 4 - 4. ASSEMBLE DOWEL MOUNT

4. 9.2. PREPARE BALSA PARTS3. ATTACH FINSC. With Fin Braces to theoutside and fin tabs to therear, glue Pod Fins to PowerPod Assembly as shown.Let dry

Page 5 - 10. ATTACH DOWEL MOUNT

WING TIPSHOULDSWING FREELY8. 5.WINGA. Lightly sand outside edgesof wing and round slightly.5. ASSEMBLE WINGB. Position wing as shown. Apply plastic ce

Page 6 - 8. INSTALL NOSE CONE INSERT

5/16" (8 mm)ELEVATORNOTCHED ENDTO REARPIVOT BASE9" (22.9 cm)6. 7.C. Apply a line of glue onto thealignment line up to the 1-1/2"(3.8 cm

Commentaires sur ces manuels

Pas de commentaire

Estes 1265 – Scissor Wing Transport Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement aérien Estes 1265 – Scissor Wing Transport. Estes 1265 – Scissor Wing Transport User Manual [en] [fr] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Estes 1265 – Scissor Wing Transport